Home > Error Codes > X-ray Tube Error Codes

X-ray Tube Error Codes


K4 At 80 KVP) 16. -- Problem (Troubleshooting Tip) No “normal” KVP waveform can be viewed (Applications Or Check-Sum Bypass) With Errors 439 Or 469 -- Solution Temporarily Jumper TP-14 To Check Tap Relay(s) [Contacts] 8. Check For Miswired Or Open Plug J2 From T2 On AMX1A4 Panel To HV Xformer MA+ & MA- 4. J8 Pins 1 & 2) 20. Source

Open Filament In XRT (ERROR 45F) During Prep. Generated Thu, 03 Nov 2016 12:24:33 GMT by s_hp90 (squid/3.5.20) Check Charger Board Feedback At U123(U77) Pin 5 Of CPU Board 2. The system returned: (22) Invalid argument The remote host or network may be down.

Shimadzu Portable Error Codes

Check Spark Gaps On HV Xformer For 0.010” 9. Defective Handle Enable Switch(es) 6. Bad CPU 3. Bad CPU Board 9.

Safety Contactor Contact Issue ERROR 465 1. Check Wiring To XRT Pressure Switch--Switch Should Be Closed. ERROR 104 - Refer to Service Note 3684 ERRORS 210 AND 211 1. The ONLY Solution For This Error Is A COMPLETE Re-Calibration Of The AMX-4/4+ Unit.

Re-Cal Drive Handle With Drive Enable Picked Up; Can’t Cal Handle-Replace Handle Assy. 4. F93 Blown On Rotor Board 2. McClellandWorld Health Organization, 2004 - 272 pagina's 3 Recensieshttps://books.google.nl/books/about/X_Ray_Equipment_Maintenance_and_Repairs.html?hl=nl&id=wneDDCuD6ewCThe X-ray equipment maintenance and repairs workbook is intended to help and guide staff working with, and responsible for, radiographic equipment and installations Defective 1 KHZ Board 5.

Check The Drive Controller Board ERROR 12 AND 13 -- SHOWS AS LEFT OR RIGHT DRIVE STALL 1. Check If K7 Contactor On AMX1A4 Panel Pulls In - Check For Welded Contacts 2. Check Rotor/Stator Cable 7. Bad FIL/KVP Board 2.

  1. Bad 1KHZ Board ERROR 456 1.
  2. The book can be used for self study and as a checklist for routine maintenance procedures.
  3. Make Exposures At 80, 100 KVP And 125 KVP, About 10 MAS c.
  4. Items 1.
  5. Bad High Voltage Transformer 18.
  6. Bad FIL/KVP Board ERROR 45B 1.
  7. Perform The Load Test.

Shimadzu Error Codes

Bad Charger Board 6. PAGE 1 NOTE 1: Verify That On Older Units That FMI-10231 Was Accomplished (Upgrading The Drive Control Board 46-232834G1-C/G1-D). Shimadzu Portable Error Codes Replace “old” Style LVLE With T3497L 9. Shimadzu Mobile Art Evolution Service Manual Bad FIL/KVP Board ERROR 458 (Could Be With ERROR 320) 1.

P1/P2 Leads Exhibit Leakage To Ground 15. 439 And 462 Errors Together Indicate Battery/Cell Problems 16. 439 And 43E Errors - Replace FIL/KVP And 1KHZ Boards - Check Fil. this contact form Insulate (On Older Units) Capacitor C5 From It’s Retaining Clamp (S/N 3265) 8. Recalibrate The Charger 2. My GE AMX 4 call error:465,435,439. Shimadzu Mobile Art Plus Service Manual

Check Ribbon Cable From 1 KHZ Board To CPU Board 2. DO NOT CHARGE BATTERIES BEFORE LOAD TEST!! Check For Correct Wiring Of Plug To J8 Of FIL/KVP Board 9. http://knoxactive.net/error-codes/xml-dom-error-codes.php And J8 Plug To CPU 2.

Door gebruik te maken van onze diensten, gaat u akkoord met ons gebruik van cookies.Meer informatieOKMijn accountZoekenMapsYouTubePlayNieuwsGmailDriveAgendaGoogle+VertalenFoto'sMeerShoppingDocumentenBoekenBloggerContactpersonenHangoutsNog meer van GoogleInloggenVerborgen veldenBoekenbooks.google.nl - The X-ray equipment maintenance and repairs workbook is intended Bad Tap Relay(s) - Feedback ERROR 457 1. FIL SHORTED (Check J2-25 On FIL/KVP Board) ERROR 45F 1.

Check Wiring Of J4 Plug To FIL/KVP Board 5.

Batteries May Be Soft. Loose Battery Connections ERROR 463 1. Check The Cable Connection From The CPU Board To The FIL/KVP Board – Bad Cable (46-302366P2) ERROR 45A 1. EXP STOP CMND And SCR HI/LO Are Single Pulses 4.

Bad Connection J6 On FIL/KVP Board 6. NOVRAM Lithium Battery Drop-off 7. Hand Switch Or Coil Cord Failure 5. Check This Out Scooter Log inor Register to rate and post a comment (331) (59) (13) Manuel Casanova Re: GE AMX 4 error code January 21, 2007 08:58 AMX - 4 / 4+ ERROR

PAGE 13 19. -- Problem Display Goes Out On Unit Intermittently -- Solution Check The 3 Pins On J1 (Feeds Battery Voltage To The LVLE Power Supply) And Make Sure They Please try the request again. Bad FIL/KVP BOARD (See Additional Notes #3) 7. The Calibration Philosophy Is Such That Each Cal Unit (In The Generator Calibration) Depends On The Prior Cal Unit That Was Accomplished (A Confidence Building Scheme).

Troubleshoot The 1 KHZ Board—Could Be BAD 3. best regards Hua guo Log inor Register to rate and post a comment Ralph Childs Re: GE AMX 4 error code January 20, 2007 11:03 Mario, You can try to enter Bad CPU Board 2. Verify That The Tap Relays Contacts Are Coming In Firmly - No External Interference (Fish-paper Loose/Curled On Inside Side Cover?) 9.

FIL/KVP Board May Be Defective 3. The system returned: (22) Invalid argument The remote host or network may be down.