Home > Error Codes > X642e Error Codes

X642e Error Codes


Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times. Power printer off one to two minutes. In most cases, five digits are shown. Check connections to the to interconnect card assembly. http://knoxactive.net/error-codes/x25-error-codes.php

See "Print Log" on page 3-22. Not all error conditions have additional sub error information. Additional sub error codes display if you press and hold Start ( ) and 2 when an error message is displayed. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr.

Lexmark Error Codes

Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot. Error 920.X and 922.XX may display for a cold fuser. I truly appreciate it. Printed error codes Additional information is available by printing the error log.

Transfer Roll Error Cannot start servo operation. Try opening Tray X. Reload the paper and do a power on reset. Lexmark Ms310dn Error Codes The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages.

ERROR 23 Jam at the duplex unit. To display sub error codes (where available) When a 9xx or 2xx error displays: 1. Check fan connector and cable for loose or damaged connection. Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation.

It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. Lexmark Scan To Email Error Codes Check paper sensor flag for restricted movement or damage. The pin should enter the tower on the HVPS and depress the cover switch. Restore password × Upload manual upload from disk upload from url Thank you for your help!

Lexmark Fax Error Codes

Replace the assys in the following order 1. The transfer roller is included in the maintenance kit. Lexmark Error Codes Sign In Upload Page of 525 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands Lexmark Manuals All in One Printer Lexmark Printer Error Messages Error 922 Fuser failed to reach standby temperature.

Replace fuser assembly Replace Fuser Lexmark Fuser Error 145.XX (C520X/530X) Motor bump aligner service check 1. navigate here Action Go to "842.xx Error code service check" on page Go to "843.xx Error code service check" on page Replace the scanner control card (SCC). If no modem is installed, install a modem card. Can be system board or printhead. Lexmark Error Codes Problem

Check AC power source for noise. FRU 1 ADF CCD cable 298.02 Error code service check Scanner missing—rear side cable unplugged. email with model, primary and secondary pattern for troubleshooting info. Check This Out My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance?

It may also indicate interference between the flatbed CCD assembly and a metal bracket. Lexmark Engine Error If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. What can I do to prevent this in the future?

If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door.

Service error codes (8xx.xx) Error code 842 843 Sub codes .xx .xx Display text Service Scanner Service Scanner Description This error indicates that a scanner communications failure. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it eCommerce Solution : k-eCommerce 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Sale Feedback Lexmark Support Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. CloudFlare Ray ID: 2fbfe69e50e05432 • Your IP: • Performance & security by CloudFlare ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve Continue pressing Start and 2 until each screen of information is obtained. 3. this contact form To display sub error codes (where available) When a 9xx or 2xx error displays: 1.

Verify latch relay is operating - slowly close door and listen for interlock switch 3.